{"id":875,"date":"2026-05-15T07:42:55","date_gmt":"2026-05-15T07:42:55","guid":{"rendered":"https:\/\/foragebaler.com\/?p=875"},"modified":"2026-05-15T07:42:55","modified_gmt":"2026-05-15T07:42:55","slug":"round-baler-roller-bearings-heat-test-grease-and-replacement","status":"publish","type":"post","link":"https:\/\/foragebaler.com\/ja\/round-baler-roller-bearings-heat-test-grease-and-replacement\/","title":{"rendered":"\u4e38\u578b\u30d9\u30fc\u30e9\u30fc\u306e\u30ed\u30fc\u30e9\u30fc\u30d9\u30a2\u30ea\u30f3\u30b0\uff1a\u8010\u71b1\u8a66\u9a13\u3001\u30b0\u30ea\u30fc\u30b9\u5857\u5e03\u3001\u304a\u3088\u3073\u4ea4\u63db"},"content":{"rendered":"
\n
<\/div>\n
Baler Drive System Reference<\/span><\/p>\n

\u4e38\u578b\u30d9\u30fc\u30e9\u30fc\u306e\u30ed\u30fc\u30e9\u30fc\u30d9\u30a2\u30ea\u30f3\u30b0\uff1a\u8010\u71b1\u8a66\u9a13\u3001\u30b0\u30ea\u30fc\u30b9\u5857\u5e03\u3001\u304a\u3088\u3073\u4ea4\u63db<\/h1>\n

A round baler carries 20 to 40 bearings depending on design \u2014 roller shaft end bearings, pickup shaft bearings, tailgate hinge bearings, and idler bearings throughout the drive system. When one of these fails mid-harvest, the baler stops until the bearing is replaced. The failure is almost never sudden; the bearing announced its condition through heat and noise days or weeks earlier. This guide shows you how to read those signals before they become a stoppage.<\/p>\n

Heat Test Method<\/a>
\nGet Bearing Support<\/a><\/div>\n<\/div>\n<\/div>\n
\n

<\/p>\n

\n

Why Bearings Fail \u2014 and Why They Give Warning First<\/h2>\n

Roller bearings fail through two primary mechanisms: fatigue spalling (the rolling element and raceway surfaces develop micro-cracks from cyclic stress that eventually flake away, creating rough rolling surfaces) and lubrication failure (the lubricant film between rolling elements and raceways becomes too thin to prevent metal contact, generating friction heat that accelerates surface damage). Both mechanisms generate heat above the bearing’s normal operating temperature \u2014 and that heat is detectable days to weeks before the bearing reaches catastrophic failure.<\/p>\n

The critical insight is that a bearing running 30\u00b0F above ambient is at early warning stage. A bearing running 60\u00b0F above ambient is at the urgent replacement threshold. A bearing running 90\u00b0F or more above ambient is in its final hours before seizure or cage fracture. These temperature thresholds give you a predictive replacement window that a reactive maintenance approach \u2014 waiting until the bearing is audibly grinding or the machine vibrates \u2014 completely misses.<\/p>\n

\n
\n
+30\u00b0F<\/div>\n
Early warning<\/div>\n
Plan replacement within current season; monitor at every interval<\/div>\n<\/div>\n
\n
+60\u00b0F<\/div>\n
Urgent<\/div>\n
Replace before next baling day; bearing life measured in hours<\/div>\n<\/div>\n
\n
+90\u00b0F<\/div>\n
Critical<\/div>\n
Stop immediately; catastrophic failure imminent; do not continue operation<\/div>\n<\/div>\n<\/div>\n<\/div>\n

<\/p>\n

\n

Where Every Bearing Is \u2014 and Which Ones Wear Fastest<\/h2>\n

\"round<\/p>\n

Understanding which bearings exist and which fail first allows you to prioritize inspection time and focus your pre-season budget on the positions most likely to generate in-season failures.<\/p>\n

\n
\n
Highest Wear \u2014 Replace Every 2\u20134 Seasons<\/div>\n
\n

Main bale-forming roller shaft bearings<\/strong> \u2014 The 3\u20136 large rollers that form the bale chamber run continuously at high belt tension. Each bearing carries both radial load from belt tension and thrust load from crop pressure variations. These are the highest-priority inspection bearings on the machine.<\/p>\n

Drive roller bearings<\/strong> \u2014 The driven roller(s) that receive PTO power carry the additional torque load of the drive system on top of belt tension. Often the first to show heat symptoms under high-density baling conditions.<\/p>\n<\/div>\n<\/div>\n

\n
Medium Wear \u2014 Inspect Annually<\/div>\n
\n

Pickup reel shaft bearings<\/strong> \u2014 High rotational speed combined with exposure to crop debris and dust accelerates seal wear. Debris bypasses worn seals and acts as an abrasive in the lubricant. Check at every 50-hour service interval.<\/p>\n

Idler and tensioner bearings<\/strong> \u2014 Lower sustained load than main rollers but subjected to high-frequency vibration from belt tension fluctuations. Seals on idler bearings are often smaller and less robust than main roller seals.<\/p>\n<\/div>\n<\/div>\n

\n
Lower Wear \u2014 Monitor, Replace When Indicated<\/div>\n
\n

Tailgate hinge bearings<\/strong> \u2014 High cycle count (one complete open-close per bale) but low load per cycle. Grease retention is the primary maintenance requirement. Failure often presents as a squeal during tailgate movement rather than heat.<\/p>\n

Net wrap arm pivot bearings<\/strong> \u2014 Intermittent load, low speed. Longest typical service life on the machine. Monitor for stiffness; replace when binding causes incomplete arm travel.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n

<\/p>\n

\n

The Heat Test: Two Methods, One Decision<\/h2>\n

\"round<\/p>\n

The heat test is the primary tool for bearing condition assessment because it measures what actually matters \u2014 whether the bearing is generating more heat than it should under normal operating conditions. Two methods are available depending on your equipment access.<\/p>\n

\n
\n
\n
Method A \u2014 Preferred<\/div>\n
Infrared Thermometer<\/div>\n<\/div>\n
\n

Equipment needed:<\/strong> Non-contact infrared thermometer ($25\u2013$60 at any hardware store). Point-and-shoot operation; safe to use with baler running.<\/p>\n

Procedure:<\/strong> After 30 minutes of normal baling operation, stop the baler (disengage PTO and wait for rotation to stop). Point the thermometer at each bearing housing and record the temperature. Take readings within 60 seconds of stopping \u2014 heat dissipates quickly once rotation stops.<\/p>\n

Reference temperature:<\/strong> Also measure the ambient air temperature and the temperature of a known-good bearing (one that has shown no symptoms). Use the highest-loaded known-good bearing as your comparison baseline, not ambient air, since all bearings run above ambient at operating temperature.<\/p>\n

Result: any bearing more than 30\u00b0F above the known-good bearing = early warning; 60\u00b0F above = urgent replacement.<\/div>\n<\/div>\n<\/div>\n
\n
\n
Method B \u2014 Field Backup<\/div>\n
Back-of-Hand Touch Test<\/div>\n<\/div>\n
\n

Equipment needed:<\/strong> Nothing. Use the back of your hand (not palm), which can detect temperature more accurately than the palm.<\/p>\n

Procedure:<\/strong> After 30 minutes of baling, stop the baler and wait 60 seconds. Touch the back of your hand to each bearing housing for 2 seconds. Compare the feel to adjacent bearings. Always use the back of the hand \u2014 palm sensitivity is lower.<\/em><\/p>\n

Calibration guide:<\/strong> A bearing at 90\u2013100\u00b0F feels warm but comfortable to hold (bath water temperature). At 120\u00b0F it is noticeably hot and you pull away within 2 seconds. At 140\u00b0F+ you cannot maintain contact \u2014 this is the immediate replacement threshold.<\/p>\n

Limitation: cannot distinguish between “warm” (acceptable) and “early warning” (30\u00b0F above baseline). Use the IR thermometer when in doubt.<\/div>\n<\/div>\n<\/div>\n<\/div>\n
\n
When to Test<\/div>\n
\n
Pre-season:<\/strong> Run the baler empty at full PTO speed for 10 minutes, then test all accessible bearing positions with the IR thermometer. This establishes your baseline temperature for every bearing at the start of the season.<\/div>\n
50-hour interval:<\/strong> Repeat the heat test on all main roller bearings and the pickup shaft bearings as part of the in-season service interval. Compare to the pre-season baseline \u2014 any bearing that has risen more than 15\u00b0F from its baseline reading since the last test is developing a problem.<\/div>\n
After unusual events:<\/strong> Any time the baler experiences an overload event (heavy slug, shear bolt failure, sudden stop), test the bearings on both sides of the load path within the next 50 bales \u2014 impact loads create peak stress in bearing raceways that can initiate spalling.<\/div>\n<\/div>\n<\/div>\n<\/div>\n

<\/p>\n

\n

Grease Specification and Interval: Getting Both Right<\/h2>\n

Grease is the only lubricant barrier between rolling elements and the raceway surfaces. Using the wrong grease \u2014 incompatible with the original fill, wrong viscosity, wrong additive package \u2014 is as damaging as no lubrication at all. And over-greasing (forcing excessive grease past the seal face) is one of the leading causes of bearing seal failure, allowing crop debris to enter the bearing from outside while the displaced seal is no longer seated.<\/p>\n

\n\n\n\n\n\n\n\n\n\n
Bearing position<\/th>\nGrease type<\/th>\nNLGI grade<\/th>\n\u9593\u9694<\/th>\nAmount per zerk<\/th>\n<\/tr>\n<\/thead>\n
Main roller shaft bearings<\/td>\nLithium-complex EP<\/td>\nNLGI #2<\/td>\nEvery 25 hrs<\/td>\n2\u20133 pumps<\/td>\n<\/tr>\n
Pickup shaft bearings<\/td>\nLithium-complex EP<\/td>\nNLGI #2<\/td>\nEvery 8 hrs<\/td>\n2\u20133 pumps<\/td>\n<\/tr>\n
Tailgate hinge pins<\/td>\nLithium-complex or moly EP<\/td>\nNLGI #2<\/td>\nEvery 25 hrs<\/td>\n2\u20134 pumps<\/td>\n<\/tr>\n
PTO shaft U-joints and carriers<\/td>\nLithium-complex EP (low water washout)<\/td>\nNLGI #2<\/td>\nEvery 8 hrs<\/td>\n3\u20134 pumps<\/td>\n<\/tr>\n
Idler and tensioner shaft bearings<\/td>\nLithium-complex EP<\/td>\nNLGI #2<\/td>\nEvery 50 hrs<\/td>\n1\u20132 pumps<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n
The over-greasing caution:<\/strong> Grease enters the bearing and must exit through the seal if you pump too much. When grease forces its way past the seal from inside, it carries the seal lip outward and partially unseats it. The result: the seal no longer fully contacts the shaft or housing bore, and crop dust and debris can enter from outside. Stop greasing when you feel a distinct increase in pump resistance \u2014 that is the point where the bearing housing is full and grease is beginning to press against the seal. 2\u20133 pumps is adequate for most baler bearings; never force more than 5 pumps into a small bearing without pausing and checking for visible grease at the seal face.<\/div>\n<\/div>\n

<\/p>\n

\n

The Radial Play Test: Confirming Bearing Wear by Hand<\/h2>\n

The radial play test is a complementary method to the heat test, used specifically when the bearing is cool or when access is limited for heat measurement. It measures the physical looseness that develops as rolling elements and raceways wear, and it is the most reliable method for detecting bearings that have advanced wear but have not yet begun to generate significant heat.<\/p>\n

\n
Radial Play Test Procedure<\/div>\n
\n
\n
1<\/div>\n

Stop the baler and disengage PTO completely.<\/strong> Wait for all rotation to stop. The test is performed with the machine stationary.<\/p>\n<\/div>\n

\n
2<\/div>\n

Access the shaft end at each bearing position.<\/strong> Grip the shaft as close to the bearing housing as possible. For roller shafts, this means reaching inside the machine with guards removed \u2014 always confirm machine is fully stopped before accessing internal components.<\/p>\n<\/div>\n

\n
3<\/div>\n

Apply radial force<\/strong> (perpendicular to the shaft axis) and feel for movement. Try to move the shaft up-down and side-to-side. In a new or healthy bearing, the shaft should feel solid with zero perceptible movement. Movement of 0.5mm (about 1\/64 inch) is early wear. Movement of 1mm (1\/32 inch) or more is replacement-threshold wear.<\/p>\n<\/div>\n

\n
4<\/div>\n

Also check axial play<\/strong> (push-pull along the shaft axis). Some axial play is normal and expected in most agricultural bearings (typically up to 0.5mm). Axial play exceeding 1mm on a bearing with a retaining ring or snap ring indicates the retainer has failed or the bearing has worn enough that the rolling element is moving laterally in the raceway.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n

<\/p>\n

\n

Identifying and Ordering the Correct Replacement Bearing<\/h2>\n

\"foragebaler.com<\/p>\n

Agricultural round baler roller bearings are almost exclusively standard AFBMA\/ISO dimension series bearings \u2014 the same basic types used throughout industrial machinery. The OEM part number on the baler parts list cross-references to a standard bearing number that can be sourced from any bearing distributor, often at 30\u201350% less cost than ordering through the equipment dealer at the same quality level.<\/p>\n

\n
\n
Reading the Bearing Number<\/div>\n

Most agricultural bearings carry a number stamped on the outer ring. Common formats: 6205<\/strong> (deep groove ball bearing, 25mm bore, 52mm OD, 15mm wide); 6305<\/strong> (same bore, heavier cross-section); 30205<\/strong> (tapered roller bearing). The first digit or digits indicate the bearing type; the final two digits indicate the bore in mm (multiply by 5 for bore > bore code 04).<\/p>\n

Write bearing numbers on a label inside the baler’s access panel. You will need them when ordering at 7 AM before a day’s baling.<\/div>\n<\/div>\n
\n
Sealed vs. Open Bearings<\/div>\n

Baler roller bearings are specified as either open (requiring re-greasing through zerks) or sealed (pre-lubricated, no zerk). Open bearings last longer when properly greased but require maintenance; sealed bearings require no maintenance but have a finite lubricant life. When replacing an open bearing, always install an open bearing \u2014 sealed replacements in a position designed for zerk greasing will not allow grease injection and will fail prematurely when their factory lubricant is depleted.<\/p>\n<\/div>\n<\/div>\n

The full wear parts replacement schedule \u2014 covering bearings in the context of the baler’s other wear items including belts, chains, and tines \u2014 and the decision framework for when bearing replacement versus full shaft assembly replacement is more cost-effective is covered in the baler wear parts guide<\/a>. When bearing failure produces operational symptoms during baling \u2014 shaft noise, tracking problems, or unusual bale formation \u2014 the root-cause process for identifying the specific failed bearing is in the \u30d9\u30fc\u30e9\u30fc\u306e\u30c8\u30e9\u30d6\u30eb\u30b7\u30e5\u30fc\u30c6\u30a3\u30f3\u30b0\u30ac\u30a4\u30c9<\/a>. For the bearing specifications on the gearbox input and output shaft positions that connect to the PTO driveline, see \u8fb2\u696d\u7528\u30ae\u30a2\u30dc\u30c3\u30af\u30b9\u304a\u3088\u3073PTO\u99c6\u52d5\u7cfb\u90e8\u54c1\u306e\u4ed5\u69d8<\/a>.<\/p>\n<\/div>\n

<\/p>\n

\n

Installing a Replacement Bearing: The Four Errors That Shorten Its Life<\/h2>\n

A replacement bearing installed incorrectly will fail in a fraction of its rated life. These four installation errors are responsible for the majority of premature bearing failures on replacement bearings.<\/p>\n

\n
\n
Error 1: Hammering the outer ring<\/div>\n

Driving the bearing into its housing by striking the outer ring transmits force through the rolling elements, creating brinell marks (dents) in the raceway. Always press the outer ring for housing fits and the inner ring for shaft fits separately \u2014 never drive through the rolling elements.<\/p>\n<\/div>\n

\n
Error 2: Contaminated installation<\/div>\n

Any dust, crop debris, or metal chip introduced to the bearing during installation acts as an immediate abrasive. Clean the shaft seat and housing bore with solvent and a lint-free cloth before installation. Handle the new bearing in its packaging until the moment of installation.<\/p>\n<\/div>\n

\n
Error 3: No initial grease charge<\/div>\n

Even new open bearings have only a minimal corrosion-protection oil charge \u2014 not operating lubrication. Before installing, inject 2\u20133 pumps of the correct grease through the zerk, or manually pack the bearing cavity if it is an open type without a zerk. The first minutes of operation are when the lubricant film is most critical.<\/p>\n<\/div>\n

\n
Error 4: Not re-checking after first operation<\/div>\n

A new bearing on a shaft that has a slight taper or burr from the previous bearing’s wear groove may shift slightly during its first 50 bales of operation. Heat-test the new bearing after the first 50 bales and re-torque the bearing retainer (lock collar, snap ring, or set screw) before the machine returns to full operation.<\/p>\n<\/div>\n<\/div>\n<\/div>\n

<\/p>\n

\n

Roller Bearing FAQs<\/h2>\n
\n
\nMy baler makes a rhythmic thumping sound that gets louder with bale formation. What kind of bearing problem produces this?+<\/span><\/summary>\n
A rhythmic thump synchronized to bale rotation (one thump per revolution of the bale, getting louder as the bale grows heavier) is the classic signature of spalling damage on a main roller bearing. The spalled area on the raceway creates a slight impact each time a rolling element passes over it. As bale weight increases, belt tension increases to maintain the same compression force, which increases the bearing load \u2014 and the impact gets proportionally louder. The frequency of the thump tells you the rotation speed of the affected roller, which narrows down which roller is the source. If you can match the thump frequency to a specific roller’s shaft rotation rate, you have identified the bearing. The troubleshooting diagnostic sequence for sound-based bearing identification is in the baler troubleshooting guide.<\/div>\n<\/details>\n
\nCan I use automotive wheel bearing grease in my baler bearings?+<\/span><\/summary>\n
Automotive wheel bearing greases are typically NLGI #2 lithium or lithium-complex greases, which are generally compatible with the lithium-complex EP specification used in most agricultural bearings. The compatibility depends on the base oil viscosity and additive packages. Mixing incompatible greases \u2014 for instance, a polyurea-thickened automotive grease with a lithium-complex agricultural grease \u2014 can cause the thickener systems to interact and reduce lubricant film strength. If you know your baler is filled with lithium-complex grease and the automotive grease you have is also lithium-complex (check the product data sheet), it is safe to use for a single service interval. For the next service, flush and refill with a single consistent product to avoid long-term mixing effects. Avoid mixing any grease products unless you can confirm thickener compatibility from the product data sheets.<\/div>\n<\/details>\n
\nMy baler has been in storage for three years. Should I replace all bearings before using it?+<\/span><\/summary>\n
After three years of storage, you should not replace all bearings as a preventive measure without inspection \u2014 that would be unnecessary expense. What you should do is a thorough pre-season inspection focused on two storage-specific concerns: corrosion and grease degradation. Inspect each bearing by rotating the shaft by hand \u2014 a corroded bearing will feel rough and may have audible gritty resistance. Flush the grease zerks by injecting several pumps of fresh grease to displace any degraded or moisture-contaminated grease that may have accumulated. Then run the machine empty at full PTO speed for 15 minutes and perform the heat test on all main bearings. Any bearing that runs hot during this empty-run test should be replaced immediately. A bearing that passes the empty-run heat test at the standard threshold is unlikely to fail in the upcoming season unless it had pre-existing wear before the storage period.<\/div>\n<\/details>\n
\nHow do I know which side of a roller shaft the failed bearing is on?+<\/span><\/summary>\n
Heat test both bearing positions on the same shaft and compare temperatures. The failed bearing will be noticeably hotter than its partner on the opposite shaft end \u2014 often 30\u201350\u00b0F higher. If both bearings on the same shaft are running hot (within 10\u00b0F of each other), both are failing, probably because the shaft itself has developed a slight bow from a previous overload, which loads both bearings asymmetrically. In this case, replace both bearings and inspect the shaft for straightness by rolling it on a flat surface before reinstalling. A shaft that rocks when rolled is bent and will continue to damage replacement bearings until corrected.<\/div>\n<\/details>\n
\nIs it worth buying premium-brand bearings vs. economy replacements?+<\/span><\/summary>\n
For the main bale-forming roller bearings \u2014 the ones carrying the highest load and having the most critical consequence if they fail in-field \u2014 premium-brand bearings (SKF, FAG, NSK, or equivalent Tier 1 manufacturers) are worth their price premium. These bearings have tighter internal tolerances, higher-grade steel, and more consistent heat treatment than economy imports, all of which translate directly to longer fatigue life under the cyclic loading of bale formation. For lower-load positions (idlers, tailgate hinges, net wrap pivots), economy bearings from reputable distributors perform adequately and the cost difference is more clearly a savings opportunity. The rule of thumb: invest in quality for the two or three highest-load positions per shaft; accept economy-grade for everything else.<\/div>\n<\/details>\n
\nHow long does a round baler roller bearing typically last before needing replacement?+<\/span><\/summary>\n
Main roller bearings on a properly maintained round baler in typical commercial hay service typically last 5,000 to 12,000 bales before showing heat symptoms that indicate replacement is approaching. In excellent maintenance conditions (greased on schedule, correct grease type, protected from contamination), some bearings reach 15,000+ bales. In poor conditions (grease intervals missed, wrong grease, contamination from a failed seal), the same bearing may need replacement at 2,000\u20133,000 bales. Tracking bale count and assigning a “bearing replacement budget” of one or two main roller bearings per 5,000 bales is a practical planning framework for maintenance-intensive commercial operations. Lower-load position bearings (idlers, pickup shaft) typically outlast main roller bearings by 50\u2013100% in equivalent maintenance conditions.<\/div>\n<\/details>\n<\/div>\n<\/div>\n

<\/p>\n

\"foragebaler.com<\/p>\n

Get Bearing Specifications and Service Position Maps for Your Baler<\/h3>\n

Bearing number, load rating, and grease type for every position on your baler model documented before delivery. Our team answers bearing maintenance questions through the machine’s full service life.<\/p>\n

Get Bearing Support<\/a><\/p>\n<\/div>\n

\u7de8\u96c6\u8005: Cxm<\/p>\n<\/div>","protected":false},"excerpt":{"rendered":"

Baler Drive System Reference Round Baler Roller Bearings: Heat Test, Grease, and Replacement A round baler carries 20 to 40 bearings depending on design \u2014 roller shaft end bearings, pickup shaft bearings, tailgate hinge bearings, and idler bearings throughout the drive system. When one of these fails mid-harvest, the baler stops until the bearing is replaced. The failure is almost never sudden; the bearing announced its condition through heat and noise days or weeks earlier. This guide shows you how to read those signals before they become a stoppage. Heat Test Method Get Bearing Support Why Bearings Fail \u2014 and Why They Give Warning First Roller bearings fail through two […]<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"categories":[28],"tags":[],"class_list":["post-875","post","type-post","status-publish","format-standard","hentry","category-forage-baler"],"_links":{"self":[{"href":"https:\/\/foragebaler.com\/ja\/wp-json\/wp\/v2\/posts\/875","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/foragebaler.com\/ja\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/foragebaler.com\/ja\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/foragebaler.com\/ja\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/foragebaler.com\/ja\/wp-json\/wp\/v2\/comments?post=875"}],"version-history":[{"count":2,"href":"https:\/\/foragebaler.com\/ja\/wp-json\/wp\/v2\/posts\/875\/revisions"}],"predecessor-version":[{"id":877,"href":"https:\/\/foragebaler.com\/ja\/wp-json\/wp\/v2\/posts\/875\/revisions\/877"}],"wp:attachment":[{"href":"https:\/\/foragebaler.com\/ja\/wp-json\/wp\/v2\/media?parent=875"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/foragebaler.com\/ja\/wp-json\/wp\/v2\/categories?post=875"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/foragebaler.com\/ja\/wp-json\/wp\/v2\/tags?post=875"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}