{"id":515,"date":"2026-03-13T09:04:48","date_gmt":"2026-03-13T09:04:48","guid":{"rendered":"https:\/\/foragebaler.com\/?post_type=product&p=515"},"modified":"2026-03-13T09:04:48","modified_gmt":"2026-03-13T09:04:48","slug":"9gl-5-0-5-6-trailed-mower-rake-5m-cut-5-6m-rake-width","status":"publish","type":"product","link":"https:\/\/foragebaler.com\/ko\/product\/9gl-5-0-5-6-trailed-mower-rake-5m-cut-5-6m-rake-width\/","title":{"rendered":"9GL-5.0\/5.6 Trailed Mower Rake | 5m Cut, 5.6m Rake Width"},"content":{"rendered":"
\n

\uc81c\ud488 \uac1c\uc694<\/h2>\n

The 9GL-5.0\/5.6 trailed mower rake<\/b> from Ever-Power brings together a 5.0-meter reciprocating sickle bar cutter and a 5.6-meter spring-tine raking system on a single trailed chassis. Designed for flat pastures and gentle slopes, this combined mower rake<\/b> allows one tractor operator to cut standing forage and gather it into neat, aerated windrows during a single field pass. Compatible with wheeled tractors rated between 30 kW and 60 kW (approximately 40 to 80 HP), the machine runs off a standard 540 r\/min rear PTO and uses the tractor’s hydraulic remotes to lift and lower each working section independently. At a total weight of 1,100 kg carried entirely on its own rubber tire axle, the implement avoids overloading the tractor hitch and follows ground contours smoothly for consistent stubble height between 60 mm and 70 mm.<\/p>\n

\u00a0\"9GL-5.0_5.6-Trailed-Mower-Rake-application-1\"<\/p>\n

Farmers and forage contractors who currently run a separate disc mower followed by a wheel rake often spend twice the fuel and twice the labor hours to cover the same area. The 9GL-5.0\/5.6 eliminates that second field pass entirely. With a mowing productivity of 2.4 to 2.8 hectares per hour and a raking productivity of 3.0 to 3.6 hectares per hour at forward speeds of 6 to 7 km\/h, this machine keeps pace with even aggressive harvest schedules. The immediate windrowing also preserves leaf integrity and nutritional value, especially in protein-rich crops like alfalfa and clover, where delayed raking can cause significant dry matter loss through sun bleaching and leaf shatter.<\/p>\n<\/div>\n

<\/p>\n

\n

Technical Specifications<\/h2>\n

Before purchasing any large forage implement, buyers in South Korea and across Asia typically request a complete parameter sheet. The table below consolidates every critical measurement, rating, and capacity of the 9GL-5.0\/5.6 trailed mower rake<\/b>. These figures are taken directly from the factory specification sheet and apply to standard production units. If your operation has unusual requirements, such as non-standard PTO speeds or specialized hitch configurations, contact our technical sales team for a tailored compatibility assessment. All dimensional values are given in millimeters unless otherwise noted, and weight figures refer to the dry, unloaded condition of the implement.<\/p>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\uc544\ub2c8\uc694.<\/th>\n\ub9e4\uac1c\ubcc0\uc218<\/th>\n\ub2e8\uc704<\/th>\n\uac12<\/th>\n<\/tr>\n<\/thead>\n
1<\/td>\nModel Designation<\/td>\n\/<\/td>\n9GL-5.0\/5.6 \ud2b8\ub808\uc77c\ub7ec\ud615 \uc794\ub514\uae4e\uc774 \uac08\ud034<\/td>\n<\/tr>\n
2<\/td>\n\ud788\uce6d \ubc29\ubc95<\/td>\n\/<\/td>\nTrailed (Traction Type)<\/td>\n<\/tr>\n
3<\/td>\n\ucee4\ud130 \uad6c\uc870 \uc720\ud615<\/td>\n\/<\/td>\nReciprocating Sickle Bar<\/td>\n<\/tr>\n
4<\/td>\n\uc808\ub2e8 \ud3ed<\/td>\n\uc911<\/td>\n5.0<\/td>\n<\/tr>\n
5<\/td>\nRaking Working Width<\/td>\n\uc911<\/td>\n5.6<\/td>\n<\/tr>\n
6<\/td>\nOperational Speed Range<\/td>\nkm\/h<\/td>\n6 – 7<\/td>\n<\/tr>\n
7<\/td>\nProductivity (Area per Hour)<\/td>\nhm\u00b2\/h<\/td>\nMowing: 2.4 – 2.8 | Raking: 3.0 – 3.6<\/td>\n<\/tr>\n
8<\/td>\n\ud3c9\uade0 \uadf8\ub8e8\ud130\uae30 \ub192\uc774<\/td>\nmm<\/td>\n60 – 70<\/td>\n<\/tr>\n
9<\/td>\nRequired Tractor Power<\/td>\n\ud0ac\ub85c\uc640\ud2b8<\/td>\n30 – 60 (approx. 40 – 80 HP)<\/td>\n<\/tr>\n
10<\/td>\nPTO Input Speed<\/td>\n\ubd84\ub2f9<\/td>\n540<\/td>\n<\/tr>\n
11<\/td>\nTotal Machine Weight<\/td>\nkg<\/td>\n1100<\/td>\n<\/tr>\n
12<\/td>\nNumber of Rake Tines<\/td>\n\uac1c<\/td>\n78<\/td>\n<\/tr>\n
13<\/td>\nRake Tine Spacing<\/td>\nmm<\/td>\n71<\/td>\n<\/tr>\n
14<\/td>\nOverall Dimensions – Transport (L x W x H)<\/td>\nmm<\/td>\n3860 x 5600 x 3000<\/td>\n<\/tr>\n
15<\/td>\nOverall Dimensions – Working (L x W x H)<\/td>\nmm<\/td>\n3860 x 7600 x 850<\/td>\n<\/tr>\n
16<\/td>\n\uc6c0\uc9c1\uc774\ub294 \ub0a0\uac1c\uc758 \uc218<\/td>\n\uac1c<\/td>\n68<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n
\n

Product Highlights at a Glance<\/h2>\n

The 9GL-5.0\/5.6 stands out in the forage equipment market because it merges two essential field operations into one machine. Below is a summary of the core advantages that make this trailed mower rake<\/b> a preferred choice for farms and contractors across Asia and beyond.<\/p>\n

\n
\n

\u2702 2-in-1 Mowing and Raking<\/p>\n

Cuts and windrows forage simultaneously in one pass. The 5.0 m sickle bar and 5.6 m rake section work together so the crop is gathered into rows the moment it falls, eliminating the need for a separate raking trip.<\/p>\n<\/div>\n

\n

\ud83d\ude9c Rubber Tire Trailed Design<\/p>\n

Supported by heavy-duty pneumatic rubber tires, the full 1,100 kg machine weight rides on its own axle rather than the tractor hitch. This prevents tractor instability, reduces soil compaction, and allows stable operation on gentle slopes.<\/p>\n<\/div>\n

\n

\u2699 Hydraulic Lift for Cutter and Rake<\/p>\n

Both the cutting assembly and the raking assembly are raised and lowered through independent hydraulic circuits connected to the tractor’s rear remotes. One driver controls everything from the cabin seat without stopping.<\/p>\n<\/div>\n

\n

\ud83d\udd27 Easy Maintenance and Practical Layout<\/p>\n

The structural layout is straightforward: minimal moving parts, accessible grease points, and individually replaceable blades and tines. Routine servicing can be completed in the field without specialized tools or workshop equipment.<\/p>\n<\/div>\n

\n

\u26a1 Wide Tractor Compatibility (30-60 kW)<\/p>\n

Pairs with 40 to 80 HP wheeled tractors equipped with a rear 540 r\/min PTO output shaft. This broad power range means most mid-sized farm tractors already on your property can run this implement without upgrades.<\/p>\n<\/div>\n

\n

\ud83c\udf3e Maximum Productivity per Hour<\/p>\n

At 6 to 7 km\/h forward speed, the machine covers 2.4 to 2.8 hectares per hour mowing and 3.0 to 3.6 hectares per hour raking. The immediate windrow formation means your baler crew can follow directly behind.<\/p>\n<\/div>\n<\/div>\n<\/div>\n

\"9GL5.0_5.6-Trailed-Mower-Rake-light-1\"<\/p>\n

\n

How the Trailed Mower Rake Works: Operating Principles and Field Procedure<\/h2>\n

Understanding the step-by-step operation of a trailed mower rake<\/b> helps operators get the most from each harvest day and avoid costly mistakes. The 9GL-5.0\/5.6 uses a straightforward mechanical sequence that any experienced tractor driver can master within a few hours of hands-on practice. The entire workflow, from connecting the machine to forming finished windrows, involves four distinct phases described below.<\/p>\n

\ud83d\udd17 Power Engagement and Driveline Connection<\/h3>\n

The operator backs the tractor to the implement drawbar and connects the towing pin. Two hydraulic hoses are routed to the tractor’s rear remotes: one controls the cutter bar lift, and the other controls the rake lift. The shielded PTO driveshaft is then coupled to the tractor’s 540 r\/min power take-off spline. Before engaging the PTO, the operator should verify that all protective shields are in place and that the driveshaft telescopes freely without binding.<\/p>\n

Once the PTO is engaged, rotational power flows through the main gearbox and an eccentric pitman arm converts it into the reciprocating lateral motion that drives the 68 cutting blades back and forth across the stationary guards. The entire engagement process from parking to moving takes roughly five minutes for a practiced crew. New operators should refer to the included manual for the correct torque settings on the PTO shaft locking collar to prevent loosening during extended field runs.<\/p>\n

\"9GL-5.0_5.6<\/p>\n

\u2b07 Hydraulic Deployment and Height Adjustment<\/h3>\n

With the PTO spinning, the operator activates the first hydraulic remote to lower the 5.0-meter sickle bar. Ground-contact skid shoes at each end of the cutter bar maintain the desired stubble height of 60 to 70 mm, which protects the root crown and promotes rapid regrowth. The second remote lowers the 5.6-meter rake assembly into its working position just behind and slightly above the freshly cut stubble.<\/p>\n

Because these two functions are independent, the operator can raise the cutter over an obstacle, such as a drainage ditch or a rock pile, while keeping the rake active to gather any remaining loose material on the ground. This hydraulic independence is one of the defining advantages of an integrated mower rake<\/b> compared to a rigidly mounted combination tool. It also means you can use the machine purely as a rake by locking the cutter bar in the transport position, giving you a dedicated 5.6-meter raking width for secondary passes after rain delays.<\/p>\n

\ud83c\udf3e Cutting, Raking, and Windrow Formation<\/h3>\n

Moving forward at 6 to 7 km\/h, the sickle bar shears standing forage at the base. Unlike rotary disc mowers that use high-speed impact to chop stems, the reciprocating action produces a clean cut with minimal stem bruising, which is particularly important for high-value legume crops. Immediately behind the cutter, 78 spring steel tines spaced 71 mm apart sweep the fallen crop inward toward the center of the machine.<\/p>\n

This raking action creates a continuous, fluffy windrow that sits on top of the stubble, allowing air to circulate freely underneath. The result is faster natural drying and higher bale quality when the windrow is picked up by a round baler or a large square baler following directly behind. One operator, one tractor, and one pass is all it takes to prepare an entire paddock for baling. For farms with tight schedules, the baler can literally trail 50 meters behind the mower rake to minimize total harvest cycle time.<\/p>\n

<\/p>\n

Structural Design and Key Engineering Features<\/h2>\n

The 9GL-5.0\/5.6 is built to survive heavy daily use in demanding field conditions. Every structural element, from the main frame to the smallest tine bolt, has been selected for long service life and ease of replacement. The machine’s design philosophy centers on keeping things simple and accessible: fewer moving parts mean fewer failure points, and modular component mounting means faster field repairs when wear items need swapping.<\/p>\n

Tubular Steel Frame and Trailed Chassis<\/h3>\n

The backbone of the machine is a thick-walled carbon steel tubular frame. This frame supports both the cutter bar assembly and the rake assembly while absorbing the torsional and bending forces generated during high-speed operation. Because the implement is trailed rather than mounted on the tractor’s three-point hitch, the full 1,100 kg weight rides on a dedicated axle fitted with agricultural-grade rubber pneumatic tires.<\/p>\n

This arrangement has two practical benefits: it keeps the tractor light on its front axle for safe steering, and it allows the implement to follow ground contours independently of tractor pitch. On uneven pastures, a trailed design consistently outperforms mounted alternatives in cut quality and operator comfort. The drawbar connection point uses a standard agricultural pin-and-clevis arrangement, compatible with essentially all wheeled tractors in the 40 to 80 HP class.<\/p>\n

Reciprocating Sickle Bar Cutter Assembly<\/h3>\n

The cutting mechanism spans 5.0 meters and consists of 68 high-carbon forged moving blades that slide over a matching set of stationary guards bolted to the cutter bar. Power reaches the blade assembly through an eccentric pitman arm driven by the PTO gearbox. As the pitman rotates, it pushes the entire knife bar left and right in a rapid reciprocating motion, creating thousands of precise shearing actions per minute.<\/p>\n

Each blade section is individually replaceable, so a single chipped or worn section can be swapped in the field using standard hand tools without pulling the entire knife bar apart. This design philosophy keeps downtime short and spare parts costs low. The guards themselves are hardened and resist mushrooming under normal use, though they should be inspected at mid-season for deformation caused by rock strikes or accumulated wear along the cutting edge.<\/p>\n

\n\n\n\n\n
\"9GL-5.0_5.6-Trailed-Mower-Rake-detail-1\"<\/td>\n\"9GL-5.0_5.6-Trailed-Mower-Rake-detail-4\"<\/td>\n<\/tr>\n
\"9GL-5.0_5.6-Trailed-Mower-Rake-detail-3\"<\/td>\n\"9GL-5.0_5.6-Trailed-Mower-Rake-detail-2\"<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

Spring-Tine Hay Rake Section<\/h3>\n

Positioned directly behind the cutter, the raking section covers a 5.6-meter working width using 78 spring steel tines. The tines are mounted on a rotating drum or bar that sweeps the cut forage inward. At a spacing of 71 mm, the tine arrangement is wide enough to let loose dirt and pebbles fall through while still capturing virtually all cut stems and leaves.<\/p>\n

This balance is important for producing clean windrows that are free of soil contamination, which directly affects silage quality and bale density. The entire rake assembly lifts hydraulically when not in use, and individual tines can be unbolted and replaced without special tools. Spare tines are inexpensive and commonly stocked at regional agricultural supply warehouses throughout Korea and neighboring countries. For operations that use the machine extensively, keeping a box of 20 to 30 replacement tines on hand is a practical investment.<\/p>\n

 <\/p>\n<\/div>\n

<\/p>\n

\n

Practical Field Applications for the Trailed Mower Conditioner with Raking Function<\/h2>\n

Versatility is a core selling point of the 9GL-5.0\/5.6. While some forage equipment is narrowly designed for one type of crop or one type of terrain, this trailed mower conditioner with raking function<\/b><\/a> adapts to a wide range of farming scenarios. The sections below outline the most common applications where the machine delivers measurable advantages over running separate mowing and raking equipment.<\/p>\n

\ud83c\udf3f Large-Scale Grass Hay Production<\/h3>\n

Producers who grow timothy, orchard grass, ryegrass, or native prairie grasses for the commercial hay market need to harvest large acreages quickly, especially when weather windows are unpredictable. Running a combined mower and rake system at 6 to 7 km\/h with an effective working width of over 5 meters means a single operator can cover 20 to 25 hectares in a standard workday. The windrows formed are immediately ready for a baler, cutting the total harvest turnaround from two or three days down to one.<\/p>\n

For export-oriented hay operations in Korea and Japan, where hay quality premiums are high, the immediate windrowing preserves the green color and leaf attachment that buyers demand. A delay of even four to six hours between cutting and raking in summer heat can cause visible sun-bleaching on the top layer of the swath, reducing the commercial grade of the final bale.<\/p>\n

\"9GL-5.0_5.6-Trailed-Mower-Rake-application-2\"<\/p>\n

\ud83c\udf3e Alfalfa and Legume Forage Harvesting<\/h3>\n

Alfalfa and other legumes are among the most nutrient-dense forage crops, but they are also the most sensitive to mechanical damage. Every time a separate rake passes over a cured alfalfa swath, leaves detach and fall to the ground. Since leaves contain roughly 70 percent of the plant’s protein, this loss directly reduces the feed value of the final bale. The mower rake<\/b> eliminates one entire raking pass, keeping those leaves attached to the stems.<\/p>\n

Dairy farms that rely on high-protein alfalfa hay or haylage see measurable improvements in milk production when they switch from a two-pass system to an integrated single-pass harvesting approach. The gentle reciprocating cut also avoids the aggressive stem bruising caused by high-speed rotary mowers, further preserving nutrient integrity through the drying and baling process.<\/p>\n

\ud83c\udfe1 Mixed Farming Operations with Limited Equipment<\/h3>\n

Smaller farms in Gyeonggi-do, Chungcheong, and other provinces often cannot justify the capital expense of owning both a standalone \uc794\ub514 \uae4e\ub294 \uae30\uacc4<\/b> or disc mower and a separate rotary rake. The 9GL-5.0\/5.6 consolidates two machines into one, reducing the initial investment, cutting annual maintenance costs, and freeing up shed space.<\/p>\n

For these operations, the trailed configuration also means the machine can be paired with whatever mid-range tractor is already on the farm, without needing a high-horsepower upgrade. A 50 HP wheeled tractor handles the combined workload comfortably in most forage conditions. The one-machine approach is also popular with agricultural cooperatives in Korea, where a single unit is shared among multiple member farms during the cutting season.<\/p>\n

\u26f0 Gentle Slope and Hillside Pastures<\/h3>\n

Flat terrain is ideal, but many grazing operations in Korea’s mountainous interior and in countries like Mongolia and Vietnam include gently sloping pastures. Because the 1,100 kg implement weight is supported by its own trailed wheels rather than hanging off the tractor’s rear linkage, the machine maintains stable lateral balance on mild inclines. This design greatly reduces the tipping hazard that comes with heavy three-point mounted mowers operating across slopes.<\/p>\n

On slopes, the recommended operating speed is at the lower end of the 6 to 7 km\/h range, and front ballast weights on the tractor help maintain steering authority. The hydraulic lift system allows the operator to raise the cutter bar quickly if the terrain suddenly steepens or transitions to rocky ground, protecting both the machine and the tractor from sudden loading events.<\/p>\n<\/div>\n

<\/p>\n

\n

Maintenance Guide and Seasonal Care for Your Mower Rake<\/h2>\n

Regular maintenance extends the working life of any forage implement and prevents small issues from becoming expensive field breakdowns. The 9GL-5.0\/5.6 is designed with serviceable components that can be inspected, adjusted, or replaced without specialized workshop equipment. Below is a practical maintenance schedule organized by frequency, along with tips that experienced operators have shared after running this machine through multiple harvest seasons.<\/p>\n

\ud83d\udd04 Daily and Per-Shift Checks<\/h3>\n

Before starting each shift, complete the following inspection routine:<\/p>\n