{"id":1261,"date":"2026-07-30T03:17:43","date_gmt":"2026-07-30T03:17:43","guid":{"rendered":"https:\/\/foragebaler.com\/?p=1261"},"modified":"2026-07-30T03:17:43","modified_gmt":"2026-07-30T03:17:43","slug":"square-baler-maintenance-schedule-and-service-checklist","status":"publish","type":"post","link":"https:\/\/foragebaler.com\/zh\/square-baler-maintenance-schedule-and-service-checklist\/","title":{"rendered":"\u65b9\u6346\u6253\u6346\u673a\u7ef4\u62a4\u4fdd\u517b\u8ba1\u5212\u548c\u670d\u52a1\u68c0\u67e5\u6e05\u5355"},"content":{"rendered":"
\n
\n
<\/div>\n
\n

Maintenance Guide \u00b7 All 9YF Models \u00b7 Annual, Pre-Season and Daily<\/p>\n

\u65b9\u6346\u6253\u6346\u673a\u7ef4\u62a4\u4fdd\u517b\u8ba1\u5212\u548c\u670d\u52a1\u68c0\u67e5\u6e05\u5355<\/h1>\n

A square baler contains a precision knotter mechanism that ties thousands of knots per season. Unlike most farm machinery where wear manifests as reduced output, baler mechanism wear manifests as missed ties \u2014 at the worst possible moment, in the field. A scheduled maintenance programme prevents the failures that cost bales, time and buyer relationships. This guide provides complete service schedules for every interval from daily to annual.<\/p>\n

Covers: annual pre-season service \u00b7 daily session checklist \u00b7 5,000-bale mid-season \u00b7 knotter service \u00b7 lubrication guide \u00b7 end-of-season storage \u00b7 parts inventory<\/p>\n

\u67e5\u770b\u65b9\u6346\u6253\u6346\u673a\u7cfb\u5217<\/a>
\n\u83b7\u53d6\u6280\u672f\u652f\u6301<\/a><\/div>\n<\/div>\n<\/div>\n

Why Scheduled Maintenance Matters More on a Baler Than Most Farm Equipment<\/h2>\n

On most farm machinery, wear is proportional and gradual \u2014 a worn mower blade cuts slightly less cleanly; a worn tractor tyre loses some traction. The operator notices the change and responds. On a square baler, the knotter mechanism operates within tolerances measured in millimetres. A cam follower that has worn 1.5mm beyond specification, or a bill hook that has developed a 2mm flat spot on its tip face, will not show any change in operation \u2014 until it misses a tie. And missed ties do not occur gradually: they occur suddenly, consistently, and at the worst possible time in the field.<\/p>\n

Scheduled service prevents this failure mode by replacing or adjusting components before they reach the point of failure \u2014 not in response to failures after they occur. The total cost of annual baler service (parts plus 2\u20133 hours of labour) is typically $300\u2013$600. The cost of one field session of missed ties \u2014 in crop loss, bale recovery labour and buyer relationship damage \u2014 can exceed this figure many times over. Annual service is not an optional maintenance cost: it is a fundamental operating requirement for reliable knotter performance.<\/p>\n

Annual Pre-Season Service \u2014 Complete Checklist<\/h2>\n

Complete this service 2\u20134 weeks before your first baling session. Allow time to order and receive any parts identified during inspection.<\/p>\n

\"9YF-2200<\/p>\n

\n
\n
Knotter System \u2014 Complete Annual Replacement and Inspection<\/div>\n
\n
\n
Replace both knife blades regardless of apparent condition.<\/strong> Knife blades are annual replacement items \u2014 dull blades fail between seasons or during the first session. Budget approximately $40\u2013$80 for a blade set.<\/div>\n

 <\/p>\n

Inspect both bill hook tips against the operator manual profile specification.<\/strong> Any flat spot, chip or rounding requires replacement. Replace both as a matched pair \u2014 never replace one only.<\/div>\n

 <\/p>\n

Measure cam follower tip radius with calipers.<\/strong> Compare to operator manual specification. Tip worn more than 1.5mm beyond specification requires replacement before the season.<\/div>\n

 <\/p>\n

Inspect tension disc faces.<\/strong> Smooth faces with no wear grooves. Scored or grooved disc faces should be replaced or resurfaced. Test: run a fingernail across the face \u2014 any groove that catches the nail is too deep.<\/div>\n

 <\/p>\n

Thread a cloth along the full twine path from spool to needle.<\/strong> Any snag point requires the responsible eyelet to be smoothed or replaced.<\/div>\n

 <\/p>\n

Check needle arm alignment at maximum travel.<\/strong> Tip position should match the operator manual specification within 3mm. A bent arm requires replacement.<\/div>\n

 <\/p>\n

Run 20 test bales at the pre-season service site.<\/strong> Zero missed ties required before certifying the knotter system ready for the season. Any miss requires re-inspection and adjustment before first customer or personal baling session.<\/div>\n

 <\/p>\n<\/div>\n<\/div>\n<\/div>\n

\n
Pickup and Feeder<\/div>\n
\n
\n
Count and inspect all pickup tines.<\/strong> Replace any missing, bent or shortened tines. At 3,000+ bales per season, replace all tines as a full set annually regardless of individual condition.<\/div>\n

 <\/p>\n

Test pickup hub bearing radial play.<\/strong> Grasp the reel tube near each hub and push radially. Acceptable play is under 1mm. Replace bearing pair if play exceeds 2mm or grinding is felt during slow rotation by hand.<\/div>\n

 <\/p>\n

Inspect fork feeder tines for bends and missing units.<\/strong> Replace individual bent tines; replace the full fork if more than 2 adjacent tines are missing or severely bent.<\/div>\n

 <\/p>\n<\/div>\n<\/div>\n<\/div>\n

\n
Chamber and Drive Train<\/div>\n
\n
\n
Measure chamber internal width at 3 points.<\/strong> Compare to operator manual specification. Over-spec by more than 3mm = wear strip replacement required this service or next season.<\/div>\n

 <\/p>\n

Measure density spring free length.<\/strong> Compare to specification. Reduction of 8%+ from specification requires spring set replacement to restore correct maximum bale density.<\/div>\n

 <\/p>\n

Check drive chain deflection against specification.<\/strong> Correct: 10\u201315mm at mid-span under moderate hand pressure. Measure chain elongation across 10 links \u2014 elongation over 2% from new-chain length requires chain replacement.<\/div>\n

 <\/p>\n

Inspect drive and driven sprocket teeth for shark-fin wear profile.<\/strong> Any hooked tooth profile requires sprocket replacement \u2014 a worn sprocket destroys a new chain rapidly.<\/div>\n

 <\/p>\n

Check gearbox oil level and condition.<\/strong> Oil on white cloth: golden to slightly dark = acceptable; milky = water contamination; metal particles = internal damage. Change oil if contaminated or per manual interval.<\/div>\n

 <\/p>\n

Inspect PTO shaft, CV joints and telescoping section.<\/strong> Correct telescoping movement, no cracked boots, grease nipples clear. Replace any cracked shield or kinked inner tube.<\/div>\n

 <\/p>\n

Verify shear bolt grade and check shear bore for oval wear.<\/strong> Replace shear bolt with fresh bolt of specified grade. Inspect bore \u2014 any ovality requires component replacement before the season.<\/div>\n

 <\/p>\n<\/div>\n<\/div>\n<\/div>\n

\n
Frame and Safety<\/div>\n
\n
\n
Inspect all structural welds with a torch under raking light.<\/strong> Any radial crack from a weld toe requires workshop repair before the season. Do not operate with known cracks.<\/div>\n

 <\/p>\n

Confirm all guards and covers are present, undamaged and correctly secured.<\/strong> Missing guards are a safety failure and a regulatory issue \u2014 order replacements before operating.<\/div>\n

 <\/p>\n

Grease all fittings to specified capacity.<\/strong> Refer to the lubrication section below for fittings list and intervals.<\/div>\n

 <\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n

Daily Pre-Session Checklist (10\u201315 Minutes)<\/h2>\n

Complete before every baling session. This takes 10\u201315 minutes and prevents the field failures that cost 60\u2013120 minutes to diagnose and repair on-site.<\/p>\n

\n
\n
Twine Path Check<\/div>\n

Pull each twine by hand from needle eye to spool. Smooth, consistent resistance throughout. Any snag point = check the corresponding eyelet and resolve before starting.<\/p>\n<\/div>\n

\n
Spool Check<\/div>\n

Verify both spools have sufficient twine for the planned session. A 400-bale session at 5m per bale requires 2,000m \u2014 one 6,500m spool per side is sufficient. Carry a spare spool per side loaded and ready.<\/p>\n<\/div>\n

\n
Shear Bolt Inspection<\/div>\n

Visually confirm the shear bolt is present and complete. If the previous session required a shear bolt replacement, confirm the replacement bolt is the correct grade \u2014 not a hardware store substitute.<\/p>\n<\/div>\n

\n
Pickup Tine Visual<\/div>\n

Walk along the pickup and count tines. Any missing tines from the last session = replace before starting. A missing tine discovered at day start takes 3 minutes to replace; the same discovery in the field takes 30 minutes and leaves a stripe of crop on the ground until resolved.<\/p>\n<\/div>\n

\n
PTO Guard Secure<\/div>\n

Confirm the PTO shaft guard is correctly attached at both the tractor and baler ends and rotates freely over the shaft. A missing or loose PTO guard is the highest injury risk on a square baler.<\/p>\n<\/div>\n

\n
Grease Key Fittings<\/div>\n

Grease the pickup hub bearings and knotter cam followers at every session (or every 8 hours per operator manual). Keep a grease gun on the machine \u2014 taking it to the field prevents the daily greasing step from being skipped.<\/p>\n<\/div>\n

\n
Field Spare Kit Present<\/div>\n

Confirm the spare parts bag is on the machine before leaving the yard. A spare kit left in the workshop is not useful in a field 8 miles from the barn.<\/p>\n<\/div>\n

\n
Run 3 Lead Bales First<\/div>\n

Bale 3 lead-in bales from the start of the windrow. Examine every knot on the first 3 bales before proceeding. Zero missed ties before entering full production. Any miss = stop and inspect the knotter.<\/p>\n<\/div>\n<\/div>\n

Mid-Season Service \u2014 At 5,000 Bales or Mid-Season Point<\/h2>\n

\"9YF-2200S<\/p>\n

\n
\n
Grease all fittings \u2014 full round<\/div>\n

Grease consumption is highest during the first half of a high-season session. Mid-season re-greasing of all fittings \u2014 not just the daily key fittings \u2014 refreshes the protection on bearings that have run hot during peak summer baling.<\/p>\n<\/div>\n

\n
Re-inspect bill hook tips<\/div>\n

A bill hook tip that was borderline at the pre-season inspection may have crossed the replacement threshold at 5,000 bales. A 5-minute inspection with a fingernail test determines whether replacement before the second half of the season is warranted.<\/p>\n<\/div>\n

\n
Check drive chain deflection<\/div>\n

Chains stretch in service \u2014 a chain that was within specification at the pre-season service may need tension adjustment by mid-season. If chain deflection now exceeds 18mm under moderate hand pressure, adjust the chain tensioner.<\/p>\n<\/div>\n

\n
Run 10 verification bales<\/div>\n

After mid-season service, run 10 bales and check every knot. The mid-season service is not complete until the 10-bale verification confirms zero missed ties and clean rope cut faces.<\/p>\n<\/div>\n<\/div>\n

Lubrication Guide and Grease Points<\/h2>\n

\"square<\/p>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n
Component \/ Location<\/th>\n\u95f4\u9694<\/th>\nGrease \/ Oil Type<\/th>\n\u7b14\u8bb0<\/th>\n<\/tr>\n<\/thead>\n
Pickup hub bearings (\u00d72)<\/td>\nEvery session<\/td>\nEP lithium grease #2<\/td>\nMost critical daily fitting. Under-greased bearings fail in 1\u20132 seasons.<\/td>\n<\/tr>\n
Knotter cam follower (\u00d72)<\/td>\nEvery session<\/td>\nEP lithium grease #2<\/td>\nDry cam follower causes accelerated cam lobe wear. Never skip this fitting.<\/td>\n<\/tr>\n
Needle arm pivot point<\/td>\nEvery 8 hours<\/td>\nEP lithium grease #2<\/td>\nStiff needle arm causes timing shift and missed ties under load.<\/td>\n<\/tr>\n
Fork feeder pivot and linkage<\/td>\nEvery 8 hours<\/td>\nEP lithium grease #2<\/td>\nMultiple fittings \u2014 consult operator manual for exact count for your model.<\/td>\n<\/tr>\n
Drive chain (open chain models)<\/td>\nEvery session<\/td>\nChain oil or light machine oil<\/td>\nApply to roller face, not plates. A dry chain wears sprockets and links faster.<\/td>\n<\/tr>\n
Star wheel bearing<\/td>\nWeekly<\/td>\nEP lithium grease #2<\/td>\nStiff star wheel bearing causes slipping and inconsistent bale length.<\/td>\n<\/tr>\n
Plunger guide rails<\/td>\nWeekly<\/td>\nEP lithium grease #2<\/td>\nGuide rails carry full plunger compression load \u2014 lubrication reduces wear on both rail and plunger.<\/td>\n<\/tr>\n
Gearbox oil<\/td>\nAnnual check<\/td>\nPer manual specification<\/td>\nCheck level at pre-season service. Change oil every 3\u20135 seasons or per manual interval, whichever is first.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

\"square<\/p>\n

\u5b63\u672b\u50a8\u5b58\u51c6\u5907<\/h2>\n

End-of-season preparation is the foundation for the following pre-season service \u2014 a well-stored machine arrives at next year pre-season service in a known, clean condition rather than requiring cleaning and assessment before inspection can begin.<\/p>\n

\n
\n

\u6b65\u9aa4 1<\/span><\/p>\n

Remove all twine from the machine<\/strong> \u2014 from the spools, needle eyes and knotter mechanism. Twine left in the machine over winter collects moisture and can cause premature rust at the points of twine contact.<\/div>\n<\/div>\n
\n

\u6b65\u9aa4 2<\/span><\/p>\n

Clean the machine completely<\/strong> \u2014 blow out with compressed air or wash with low-pressure water. Accumulated crop residue holds moisture against steel surfaces and accelerates rust. Pay particular attention to the knotter area where fine chaff accumulates densely.<\/div>\n<\/div>\n
\n

\u6b65\u9aa4 3<\/span><\/p>\n

Grease all fittings a final time<\/strong> before winter storage. Fresh grease displaces moisture from bearing cavities and provides corrosion protection over the storage period. This greasing round is separate from the pre-season service greasing \u2014 both are needed.<\/div>\n<\/div>\n
\n

STEP 4<\/span><\/p>\n

Apply light oil or rust-inhibitor spray to bare metal surfaces<\/strong> \u2014 plunger face, chain links, knife blade edges, needle tips. Use a light lubricating oil, not grease \u2014 grease on the knife face attracts crop residue at the start of next season.<\/div>\n<\/div>\n
\n

STEP 5<\/span><\/p>\n

Store indoors if possible<\/strong> \u2014 a barn or equipment shed extends machine life significantly. If outdoor storage is unavoidable, use a full-coverage machine tarp secured against wind and animals, and store with all guard covers closed. Outdoor storage without a tarp is the single largest contributor to premature rust and UV-related paint and seal degradation.<\/div>\n<\/div>\n<\/div>\n

Parts Inventory to Keep On Hand<\/h2>\n
\n
Shear bolts:<\/strong> 10+ of the correct grade and size for your model. Store in a sealed labelled bag.<\/div>\n
Knife blade sets:<\/strong> 1 spare set. Replace both blades at each annual service; keep one set at the workshop and one in the field kit.<\/div>\n
Pickup spring tines:<\/strong> 8\u201312 units (full reel row). Allows full-row replacement in the field without a workshop trip.<\/div>\n
Twine guide eyelets:<\/strong> 3\u20134 spare units of each size used in the twine path on your model.<\/div>\n
Drive chain joining link:<\/strong> 1 link of the correct chain pitch. A broken chain without a spare link ends the session.<\/div>\n
Gearbox oil:<\/strong> 500ml of the correct specification. Keeps a level top-up possible at any time without a supplier trip.<\/div>\n<\/div>\n
\n

PTO and Drive Train Maintenance<\/h3>\n
\n

\n\"agricultural
\n<\/a><\/p>\n

\u6240\u67099YF\u578b\u53f7\u7684\u52a8\u529b\u8f93\u51fa\u8f74\u548c\u53d8\u901f\u7bb1\u89c4\u683c\uff1a \u519c\u4e1a\u53d8\u901f\u7bb1\u548c\u52a8\u529b\u8f93\u51fa\u8f74\u89c4\u683c<\/a><\/p>\n<\/div>\n

\n

The PTO driveshaft CV joints require annual grease through dedicated nipples on the yoke \u2014 these are separate from the tractor PTO lubrication and are the responsibility of the baler operator to maintain. A dry CV joint fails within 1\u20132 seasons. Full driveshaft specifications: PTO\u4f20\u52a8\u8f74\u548cCV\u63a5\u5934\u5c3a\u5bf8\u6307\u5357<\/a>.<\/p>\n<\/div>\n<\/div>\n<\/div>\n

Frequently Asked Questions \u2014 Square Baler Maintenance<\/h2>\n
\n
\nHow long does a full annual pre-season service take?+<\/span><\/summary>\n
A thorough annual pre-season service on a 9YF series baler takes 2.5\u20134 hours for an experienced operator who knows the machine. For a first-time service or a machine recently purchased used, allow 4\u20136 hours as unfamiliar mechanisms require more time to inspect and understand. The time is divided approximately: knotter inspection (30\u201345 min), pickup and feeder (20\u201330 min), chamber and drive train (30\u201340 min), frame and guards (15\u201320 min), lubrication (20\u201330 min), test bales including observation (45\u201360 min). The test bale observation is not optional \u2014 it is the verification that all the inspection and adjustment work produced a correctly functioning machine. A service that ends without a 20-bale test is incomplete regardless of how thorough the mechanical inspection was.<\/div>\n<\/details>\n
\nShould I service the baler myself or use a dealer service centre?+<\/span><\/summary>\n
Both approaches are valid depending on your mechanical aptitude and available time. The advantage of dealer service: technicians who service the same model multiple times per season develop knotter adjustment expertise that takes an owner-operator years of experience to match. The advantage of self-service: you develop an understanding of your specific machine condition that allows earlier identification of developing problems before they cause in-field failures. The recommended approach for most owners: have the first post-purchase service done at a dealer to establish a baseline and learn the service procedure from the technician. Then self-service in subsequent years following the checklist, with dealer involvement only when issues are identified that require workshop tools or diagnostic expertise beyond the standard checklist.<\/div>\n<\/details>\n
\nWhat grease should I use on my 9YF baler?+<\/span><\/summary>\n
The operator manual for each 9YF model specifies the grease type and consistency for each fitting. The general standard across the 9YF range is a lithium complex EP (extreme pressure) grease at NLGI Grade 2 consistency \u2014 this is available under many brand names at farm supply stores and automotive suppliers. Do not use general-purpose wheel bearing grease for high-load fittings like the pickup hub bearings and knotter cam followers \u2014 these components require the extreme-pressure additive that standard lithium grease does not contain. For the gearbox, use the oil type specified in the manual \u2014 typically an SAE 90 gear oil or per the specific gearbox manufacturer specification. Never mix different grease types in the same fitting without purging the old grease \u2014 incompatible grease types can degrade each other and reduce rather than improve lubrication effectiveness.<\/div>\n<\/details>\n
\nMy baler missed ties at the end of last season. What should I check first at the pre-season service?+<\/span><\/summary>\n
End-of-season miss-ties with no change in twine or operating conditions most commonly indicate one of three progressive wear items that crossed the failure threshold late in the season. First: bill hook tip rounding \u2014 the most common cause of developing miss-ties in the second half of a season. Measure both bill hook tips first at the pre-season service. Second: cam follower wear \u2014 a follower that was borderline at the previous pre-season service may have worn past the failure point during the season. Measure it immediately after the bill hooks. Third: knife blade edge loss \u2014 a blade that has reached the end of its useful life shifts the loop geometry slightly by not cutting cleanly, which can manifest as intermittent miss-ties in the late-season bales. Replace the blades as standard annual maintenance regardless, and inspect the bill hooks and cam follower with particular attention given the prior season miss-tie history.<\/div>\n<\/details>\n
\nHow often should I change the gearbox oil on a 9YF series baler?+<\/span><\/summary>\n
The operator manual specifies the oil change interval for each model \u2014 typically every 100\u2013200 operating hours or every 3\u20135 seasons, whichever is reached first for low-volume operations. At annual bale counts below 3,000, a 5-season oil change interval is generally acceptable provided the oil is checked annually at the pre-season service and no contamination is detected. For operations above 5,000 bales per season, shorten the interval to every 2\u20133 seasons due to higher operating hours. The condition inspection at each pre-season service is more important than the interval alone: an oil that appears dark, milky or contains metal particles should be changed immediately regardless of when it was last changed. Dark oil alone without other contamination signs \u2014 at an appropriate age \u2014 is normal and does not necessarily indicate a problem. The definitive test is the metal particle check on a white cloth: if you see bright metallic flakes on the cloth after draining a small sample, the gearbox has internal wear that should be investigated before the season begins.<\/div>\n<\/details>\n
\nCan I speed up the daily checklist to save time?+<\/span><\/summary>\n
The daily checklist takes 10\u201315 minutes \u2014 this is already optimised. Specific items can be skipped only if you have a systematic reason to know they are correct: if you checked the spare parts kit yesterday and it was not opened, you can confirm it is still complete without a full inventory. If you greased the hub bearings yesterday and have not baled since, the daily greasing can be deferred to the next session day. What cannot be safely abbreviated: the twine path pull-through check before every session (takes 2 minutes, prevents mid-session knotter failures from missed eyelets); the shear bolt visual (30 seconds); and the 3 lead-bale verification (15 minutes, non-negotiable). The 3 lead-bales should never be omitted in the name of time savings \u2014 they are the only way to confirm that any change since the last session (new twine spool, maintenance work, overnight temperature change) has not affected knotter function before committing to a full production run on time-sensitive weather-window hay.<\/div>\n<\/details>\n
\nWhat are the signs my baler needs a mid-season unscheduled service?+<\/span><\/summary>\n
Any of the following during a session is a trigger for an unscheduled service stop: a missed tie at any point in the session (do not continue past 3 consecutive bales with a miss); a shear bolt failure not clearly associated with debris in the field; grinding or knocking sound from the drive train or knotter area that was not present in the previous session; bale weight that has decreased by more than 20% of the target without any change in windrow density or settings; any visible deformation or unusual movement in the mechanism during operation. The correct response to any of these is to stop for the session, investigate the cause and address it before the next session rather than continuing and hoping the issue resolves. Continued operation with a developing mechanical problem almost always results in a more expensive repair than stopping early and addressing the root cause while the secondary damage is still limited.<\/div>\n<\/details>\n
\nHow many bales should I expect from a 9YF baler before major component replacement?+<\/span><\/summary>\n
With correct annual pre-season service and daily maintenance: bill hook pairs typically last 25,000\u201340,000 bales before requiring replacement; cam followers last 20,000\u201335,000 bales; drive chains last 15,000\u201325,000 bales if correctly tensioned and lubricated; chamber wear strips last 40,000\u201360,000 bales in standard hay. Pickup spring tines have the widest variation \u2014 from 5,000 bales in abrasive conditions (cotton stalk, silica-rich straw) to 20,000 bales in clean hay. Gearbox gears, when correctly lubricated, typically last the life of the machine without replacement. Hub bearings last 15,000\u201330,000 bales with daily greasing. These ranges are guidance, not guarantees \u2014 actual component life depends heavily on crop type, operating conditions, lubrication compliance and the accuracy of the pre-season inspection in identifying and replacing borderline components before they reach failure. A machine that skips annual service for 2 consecutive seasons will typically show multiple component failures simultaneously, at a higher total cost than 2 annual services would have prevented.<\/div>\n<\/details>\n<\/div>\n

Order Parts and Get Service Support for Your 9YF Baler<\/h2>\n
\n

For parts enquiries, operator manual requests, or technical support on any maintenance issue across the 9YF\u7cfb\u5217<\/a> \u2014 contact us with your model and serial number and we will identify the correct parts and service procedure for your specific machine.<\/p>\n

Contact for Parts and Support<\/a>
\n\u67e5\u770b\u65b9\u6346\u6253\u6346\u673a\u7cfb\u5217<\/a><\/div>\n

\n<\/div>\n

\u7f16\u8f91\uff1aCxm<\/p>\n<\/div>","protected":false},"excerpt":{"rendered":"

Maintenance Guide \u00b7 All 9YF Models \u00b7 Annual, Pre-Season and Daily Square Baler Maintenance Schedule and Service Checklist A square baler contains a precision knotter mechanism that ties thousands of knots per season. Unlike most farm machinery where wear manifests as reduced output, baler mechanism wear manifests as missed ties \u2014 at the worst possible […]<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"categories":[28],"tags":[],"class_list":["post-1261","post","type-post","status-publish","format-standard","hentry","category-forage-baler"],"_links":{"self":[{"href":"https:\/\/foragebaler.com\/zh\/wp-json\/wp\/v2\/posts\/1261","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/foragebaler.com\/zh\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/foragebaler.com\/zh\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/foragebaler.com\/zh\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/foragebaler.com\/zh\/wp-json\/wp\/v2\/comments?post=1261"}],"version-history":[{"count":2,"href":"https:\/\/foragebaler.com\/zh\/wp-json\/wp\/v2\/posts\/1261\/revisions"}],"predecessor-version":[{"id":1265,"href":"https:\/\/foragebaler.com\/zh\/wp-json\/wp\/v2\/posts\/1261\/revisions\/1265"}],"wp:attachment":[{"href":"https:\/\/foragebaler.com\/zh\/wp-json\/wp\/v2\/media?parent=1261"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/foragebaler.com\/zh\/wp-json\/wp\/v2\/categories?post=1261"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/foragebaler.com\/zh\/wp-json\/wp\/v2\/tags?post=1261"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}